Jag har vurdert samma løsning men har inte kommit vidare med detta än. Om det kan vara till hjälp här noen anteckningar jag gjort;
----
http://www.svalander.se/vinyl/tonarmskabel.htm
Tunn tonarmskabel 5 färger
Tvinnad av fem färger litztråd.
Varje färg är 0,2mm och består av 7 st emaljerade trådar!
Total diameter 0,5mm.
En tonarmskabel av mycket god kvalitet.
24 kr / dm (60 cm = 144 kr)
----
http://www.hificollective.co.uk/components/dins.html
----
http://www.takefiveaudio.com/mall/shopexd.asp?id=486&bc=no
Cardas 33 AWG Tonearm Wire, 1 ft
CAN$2.49 / ft (singel)
White, Blue, Red, Green
http://www.takefiveaudio.com/mall/shopexd.asp?id=502&bc=no
Cardas PCC E Cartridge Clips
Cardas Economy Gold Cartridge Clips, Set of 4
We supply these complete with shrinktube.
CAN$4.95
http://www.takefiveaudio.com/mall/shopexd.asp?id=488
Cardas 4X33 Tonewire Wire, Shielded, 1 ft
Four 33 awg wires (Cardas tonearm wire) twisted then bundled in Teflon tape, braided shield and supple outer jacket. This cable makes an easy one piece rewire on your tonearm.
CAN$13.95 / ft
----
http://www.dedicatedaudio.com/inc/sdetail/3928
Cardas 33AWG 4 conductor Golden Strand Litz Tonearm Cable - Braided
$ 19.95 / ft
http://www.dedicatedaudio.com/inc/sdetail/744
Cardas PCCE Cartridge Clips
Set of 4
Cartridge Clip Heatshrink Kit (4) pcs. R/G/B/W (add $3.95)
$ 7.00
We suggest the following termination hints. The Cardas 33AWG cable is of litz construction so you must be sure the strands are heated enough to remove the "varnish like" coating. We also suggest a practice run on tinning... it takes a bit to get the hang of it without rolling back the insulation. We have also found the Cardas solder to sound the best and easiest to work.
Carefully strip the tip of insulation from the cable
Melt a bead of solder on your soldering pen tip
Clamp a single wire with a pair of "smooth" tipped tweezers at the distance you wish to solder. The tweezers act as a heatsink and grip the insulation preventing the insulation from rolling back with excess heat
Lower the stripped tip of cable into the heated bead of solder, tinning the tip of the cable (do not squeeze the tweezers too tight)
Remove the tip of the cable from the bead of heated solder and hold the cable with the tweezers until cool
Repeat for tinning of the remaining 3 cable strand tips
Using your tweezers, grip and tin the (4) cartridge clips
Again grip a tinned cable strand with the tweezers in the appropriate position to prevent insulation roll during soldering. Position tinned cable tip at phono clip and heat both clip and strand at the same time with your soldering pen. No further solder is required. DO NOT OVERHEAT. Hold in position and allow to cool before releasing tweezers.
Repeat for each remaining phono lead
Slide heatshrink into position and heat
http://www.dedicatedaudio.com/inc/sdetail/8824
Cardas (4) Strand, Braided 33AWG Tonearm Cable with Soldered Clips. We have taken the challenge out of rewiring your tonearm. This Cardas production tonearm wire kit includes 24" of Cardas' famous 4 strand, braided 33 AWG Golden Ratio, Litz tonearm cable presoldered to the outstanding Cardas PCCE-R Cartridge Clips with heatshrink
$ 79.95 / 24" (60 cm)
Shipping dedicatedaudio.com
less then 1 lb $ 12.00
---
/Suomela
